[. . . ] Operating Instructions Copy/Document Server Reference 1 2 3 4 5 Placing Originals Copying Connect Copy Document Server Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine. Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Important Contents of this manual are subject to change without prior notice. [. . . ] Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. 2 F Press [OK] twice. G Place the originals, and then press the {Start} key. Center/Border Erase (same width) This mode erases both the center and edge margins of the original image. A Press [Edit / Stamp]. B Press [Erase]. E Press [Same Width]. 98 Copier Functions F Press [Center], and then set the erase center width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. 2 G Press [Border], and then set the erase border width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). H Press [OK] twice. I Place the originals, and then press the {Start} key. Center/Border Erase (different width) This mode erases both the center and edge margins of the original image. A Press [Edit / Stamp]. B Press [Erase]. D Press [Erase Center/ Border]. 99 Copying E Press [Different Width]. F Press the key you want to change and set an erase width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. 2 G Press [OK] twice. H Place the originals, and then press the {Start} key. Inside Erase This mode erases a designated area of the copy image. A Specify the point where the machine starts scanning (X1, Y1) and where it stops scanning (X2, Y2). You can input lengths of 0 - 432 mm, 0 - 17". B Press [Edit / Stamp]. C Press [Erase]. D Select one of the areas from [Erase Inside 1] to [Erase Inside 5]. 100 Copier Functions E Enter the value of [X1] with the number keys, and then press [q]. 2 F Enter the value of [Y1] with the number keys, and then press [q]. H Enter the value of [Y2] with the number keys, and then press [q]. If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. I Press [OK]. K Place the originals, and then press the {Start} key. Outside Erase This mode erases all areas of the copy image other than the area you have selected. If you want to go on to erase another area, repeat from steps D to I. A Specify the point where the machine starts scanning (X1, Y1) and where it stops scanning (X2, Y2). [. . . ] Date Stamp · When using Combine mode, the date stamp is printed as follows: · With the Combine function 5 AMG067S · With the Magazine or Booklet function AMG068S 196 Supplementary Information Page Numbering · When page numbering is used with Combine mode, page numbers are printed as follows: · Page Numbering per original: With 1 Sided/2 Sided using the Combine function GCANPE0E With the Magazine or Booklet function 5 GCANPE1E · Page Numbering per copy: With 1 Sided/2 Sided using the Combine function GCANPE2E · If you combine this function with the Duplex (Top to Top) function and select [P1, P2. . . ] or [1/5, 2/5. . . ], page numbers on the back are printed as follows: GCSTMPBE A B Front Back 197 Appendix Front Cover, Back Cover · If Blank mode is selected, the cover will not be counted as a copy. · Front and back covers are two-sided copied depending on the settings made in Display Time in Cover Sheet Tray of User Tools (System Settings). Designate · When "Combine (1 Sided2 Sided)" has been selected, specified pages will always be copied on the front of copies in the same way as in Chapters mode. Slip sheet · If you do not copy onto slip sheets, they are excluded from the number of copies counted. [. . . ]